Launch Slideshow

Error: less than 300px wide output not yet supported

Texas-Sized Formwork

Texas-Sized Formwork

  • Image

    http://www.theconcreteproducer.com/Images/tmp586%2Etmp_tcm77-1298758.jpg?width=150

    true

    Image

    150

    Bexar Concrete Works I used Hamilton Forms' 11-foot forms to create 97-foot prestressed concrete haunch girders.

  • Image

    http://www.theconcreteproducer.com/Images/tmp587%2Etmp_tcm77-1298762.jpg?width=150

    true

    Image

    150

    The super-sized girders will be part of a new DART light rail system connecting downtown Dallas with the Dallas/Fort Worth International Airport.

  • Image

    http://www.theconcreteproducer.com/Images/tmp588%2Etmp_tcm77-1298766.jpg?width=150

    true

    Image

    150

  • Image

    http://www.theconcreteproducer.com/Images/tmp589%2Etmp_tcm77-1298769.jpg?width=150

    true

    Image

    150

  • Image

    http://www.theconcreteproducer.com/Images/tmp58A%2Etmp_tcm77-1298773.jpg?width=150

    true

    Image

    150

  • Image

    http://www.theconcreteproducer.com/Images/tmp58B%2Etmp_tcm77-1298777.jpg?width=150

    true

    Image

    150

  • Image

    http://www.theconcreteproducer.com/Images/tmp58C%2Etmp_tcm77-1298780.jpg?width=150

    true

    Image

    150

The Dallas area Rapid Transit Authority's (DART) 45-mile light rail system is one of the best in the nation. With funds from the American Recovery and Reinvestment Act, DART has launched a major expansion.

One section of the rail system will travel over a 550-foot prestressed concrete bridge spanning the Trinity River levy. The 260-foot center span consists of 97-foot-long x 10-foot, 10-inch-tall haunch girders at the piers and a middle drop beam section 160-foot-long x 6-foot, 10-inches-tall. The end and center spans of the bridge are typical TX82 girders.

The precast/prestressed producer, San Antonio-based Bexar Concrete Works I, chose Hamilton Form Co. in Fort Worth, Texas, to build forms for the project. “On a complex design/build project of this magnitude, the forms play a critical role in the project's success,” says Bexar's Jorge Hinojosa.

To cast the 97-foot-long haunch girders, Hamilton Form built 11-foot, 2-inch-tall haunch sideforms and a 33-inch-wide soffit. The soffit slopes 4 feet in the middle to create the drop in the center of the beam. “We built a sloped soffit instead of sloped sideforms to make it easier for the customer to set up the formwork,” says Taylor Slate, engineering manager. “The formwork is built in sections. Each section of soffit and sideforms is matched and marked on a dead level working jig, and we set up and check the forms before shipping.”

The manufacturer sealed the form against the soffit with a thru tie system 2 inches below the bottom casting surface. Top ties and thru ties were spaced closer together in the maximum height area of the girder for added support. Vi-brotrack was installed to slide vibrators along the form to consolidate the concrete. Two pour openings prevented the concrete from dropping the full height of the form during the pour.

Visit Hamilton Form at booth #424 at the PCI Show and at www.hamiltonform.com.

Following are more suppliers of precast and prestressed concrete forms.

Light-duty forms

Light-duty bases, risers, and flat top forms are up to 72 in. in diameter and are fabricated with a thinner steel plate and a slightly lighter gage of channel rib reinforcing, for a typical cost savings of 25% compared to traditional forms. All other parts of the form are exactly the same. Besser Co. 800-968-0444. www.besser.com


Precast bollards

The Precast Bollard is a polyethylene pipe with a domed top that is designed to be filled with concrete for added strength. The shell, available in standard or custom colors, eliminates the painting and maintenance of steel pipes. The 7 ft.-tall forms are available in 4- and 7.5-in. diameters. Strike Products. 800-262-4129. www.striketool.com


Cast natural looking walls

CreteWood and CreteStone concrete retaining walls feature realistic wood grain and stone textures. Precast panels up to 5 ft. long fit together with an interlocking design. Licensed manufacturers receive a turnkey system of mold boxes, specific concrete mix, a coloring process, and marketing support. CreteWood Products. 314-822-8572. www.cretewoodproducts.com




Lightweight modular forms

Create precast concrete structures in an infinite number of sizes and shapes with lightweight modular forms. The long-lasting, low-maintenance system consists of simple-to-use forms that help precasters make higher quality products. The heavy-duty lightweight forms include pallet and header systems. Wall-Ties and Forms Inc. 800-444-9692. www.wallties.com






High-strength metal casting

Use BMF Metal Forms for industrial, residential, and commercial jobs, including concrete sidewalks, curbs and gutters, runways, median barriers, and bridge parapets. The forms are sheared, punched, assembled, and welded with maximum strength and rigidity for easy setup, stripping, and reuse. RCL Enterprises. 315-532-1530. www.jaquith.com


Box culverts

The Wedge-It box culvert wet casting form uses wedge motion to release the concrete inner core from the mold. The form helps reduce labor costs with adjustable legs, and header and pallet rings, and a no-hinge design. Interchangeable core and jacket panels can be adjusted to 52 sizes, up to 10 x 12 ft. Custom Welding & Fabrication Inc. 603-942-5170. www.customweldinginc.com

For more information, visit www.theconcreteproducer.com/freeinfo