Launch Slideshow

Setting up Concrete Pumps

Setting up Concrete Pumps

  • Outriggers must be supported on cribbing large enough to spread the load to the supporting soil.

    http://www.theconcreteproducer.com/Images/pumps-cribbing_tcm77-2115372.jpg

    true

    Outriggers must be supported on cribbing large enough to spread the load to the supporting soil.

    600

    Schwing

    Outriggers must be supported on cribbing large enough to spread the load to the supporting soil.
  • To prevent damage to the outriggers, all should be fully extended.

    http://www.theconcreteproducer.com/Images/pumps-extend_tcm77-2115373.jpg

    true

    To prevent damage to the outriggers, all should be fully extended.

    600

    Schwing

    To prevent damage to the outriggers, all should be fully extended.
  • Maintaining clear access to the pump for concrete delivery is keeping construction productive and safe at the 11th Street Bridge Project in southeastern Washington D.C. Note trucks entering and exiting the site via different routes. Photo: Putzmeister

    http://www.theconcreteproducer.com/Images/pumps-open_tcm77-2115374.jpg

    true

    Maintaining clear access to the pump for concrete delivery is keeping construction productive and safe at the 11th Street Bridge Project in southeastern Washington D.C. Note trucks entering and exiting the site via different routes. Photo: Putzmeister

    600

    Putzmeister

    Maintaining clear access to the pump for concrete delivery is keeping construction productive and safe at the 11th Street Bridge Project in southeastern Washington D.C. Note trucks entering and exiting the site via different routes. Photo: Putzmeister
  • Operators will position the cribbing and then jack each outrigger individually to assure that the ground is strong enough to support the load.

    http://www.theconcreteproducer.com/Images/pumps-outrigger_tcm77-2115375.jpg

    true

    Operators will position the cribbing and then jack each outrigger individually to assure that the ground is strong enough to support the load.

    600

    Putzmeister

    Operators will position the cribbing and then jack each outrigger individually to assure that the ground is strong enough to support the load.

Of all the equipment that has changed concrete construction over the past 40 years, the concrete boom pump is number one for increasing productivity and reducing labor. While buckets and buggies are still used in some situations, they have become rare on modern concrete projects. Concrete pumps have actually expanded the applications for concrete —think how difficult filling insulating concrete forms would be without a pump; some recent high-rise concrete buildings would not have been feasible without the ability to pump the concrete hundreds of feet up to placing booms. Producers need to be involved in positioning decisions for pumps in order to maintain safety and productivity.

Safety

A concrete pump is a very large and powerful piece of equipment with its boom fully extended like a giant extraterrestrial insect. It has the ability to provide great benefits on a concrete project, but it can also be dangerous without proper set-up and safety procedures. The American Concrete Pumping Association (ACPA) has done many things to further the pumping industry, but the single most important is advancing pump safety. One big part of that is positioning the pump to assure safe operation.

In general, ACPA’s position is that the concrete contractor is responsible for providing a safe set-up area for the pump. The area must be large enough for the pump with outriggers, free of building materials, level enough that the pump can be leveled to within 3 degrees, far enough away from excavations and power lines, and with stable soil on which the outriggers can bear. Pumping contractors, however, will usually make sure that’s the case to protect themselves and their equipment and to do the best and safest job possible for their customers. “Every job is different,” says Joe Delehay, president of Dynamic Concrete Pumping, Calgary, Alberta, and also a concrete floor contractor. “So during the prepour meeting we make sure the site is safe by doing a hazard assessment to check for wires, trees, excavations, obstacles, and especially things like overpasses.”

Electrical lines are the most obvious hazard. “Like cranes,” writes ACPA, “the number one cause of fatal accidents with pumps is electrocution.” When the U.S. Department of Labor recently changed the rule for minimum clearance for cranes from power lines to 20 feet (no piece of the crane, load, or rigging can be within 20 feet of a wire), concrete pumps were specifically excluded, meaning pumps could continue to follow the previous 17-foot rule. But to simplify things, ACPA adopted the 20-foot rule anyway. For higher voltage situations (large transmission towers and lines), the rule is 50 feet minimum clearance. Pump operators should always refuse to operate the pump if it will violate the 20-foot rule.

The next most-important aspect of safely positioning a pump is to assure that it won’t tip over. When a boom is fully extended and full of concrete there could be ½ cubic yard of concrete or more in the line. That’s about one ton of concrete, enough to easily tip over a boom pump that is not properly stabilized.

Boom pumps are stabilized using outriggers, and properly deploying the outriggers is essential. The four outriggers must be fully extended and bearing on a solid surface. Never partially extend outriggers since not only is it dangerous, but the outriggers can be damaged. The foot of the outriggers alone is seldom large enough to support that load and must bear on cribbing. Operators will position the cribbing and then jack each outrigger individually to assure that the ground is strong enough to support the load. If not, dunnage will be added to increase the bearing area. The most dangerous situation for pump stability is fill or hidden voids below the surface. If you see a pile of dirt near the set-up area, that’s a sign that there could have been some excavation. Once the operator feels the outriggers are stable, he will slew the boom over each outrigger as a final safety check to see if any outriggers sinks into the soil.